Narda Safety Test Solutions S.r.l. Leader on Electromagnetic Compatibility and EMC EMI Receiver  
   English  Italiano
PMM a Brand of Narda Safety Test Solutions S.r.l. Electromagnetic Compatibility EMC EMI Instruments
 

Home
Company
Fundamentals
  EMC
  EMF
  EMI
  Properties
  Occurrence
  Effects
  Limits
Products
Services
Support
Contacts


Sales Partner of:

 A.H. Systems Inc. - Antennas
 COM-POWER Corporation
 FCC - RF Test Equipment
 HAEFELY
 Magnetic Instrumentation Inc. - Magnetic Equipment
 Prana Broadband Amplifiers
 Siepel  Shielded Rooms
Other Narda
Group Companies

 - Narda-STS (DE)
 - Narda-STS (USA)
 - Narda-East
 - Narda-West
 - Satellite Networks
 

7  Online visitors

 
  EMC

 

Electromagnetic Compatibility (EMC) is the branch of electrical sciences which studies the unintentional generation, propagation and reception of electromagnetic energy with reference to the unwanted effects (Electromagnetic Interference, or EMI) that such energy may induce. The goal of EMC is the correct operation, in the same electromagnetic environment, of different equipment which use electromagnetic phenomena, and the avoidance of any interference effects.

In order to achieve this, EMC pursues two different kinds of issues. Emission issues are related to the unwanted generation of electromagnetic energy, and to the countermeasures which should be taken in order to reduce such generation and to avoid the escape of any remaining energies into the external environment. Susceptibility or immunity issues, in contrast, refer to the correct operation of electrical equipment in the presence of unplanned electromagnetic disturbances.

Electromagnetic Interference (EMI) and Radio Frequency Interference (RFI) are usually caused by the rapid switching action of semiconductors, relays, etc. resulting in electronic pollution.  These affect the reception of broadcasts and can lead to the malfunctioning of other sensitive electrical and electronic equipment.Inverters etc. cause very severe interference over a wide frequency range, due to the very fast switching of components such as IGBTs.

Electromagnetic Interference refers to noise spread over the whole electromagnetic spectrum.  Radio Frequency Interference refers to noise over the part of the spectrum used specifically for broadcasting.

EMI can be propagated in two ways; conducted interference along input and output cables; and radiated through direct transmission, capacitive and inductive coupling etc.

A device is considered to comply with EMC when:

- both conducted and radiated interference levels are below specified limits.
- it's immunity or susceptibility to conducted and radiated interference are above specified limits.

In the past, outside the military field, EMC was not of paramount importance to equipment manufacturers and there was a relaxed EMC regime. Power input fuses on electrical appliances was just about it for the commercial world. Where high emission levels were a potential problem (such as microwave ovens), equipment manufacturers could usually avoid emissions limits through the choice of certain unlimited Industrial, Scientific and Medical (ISM) frequency bands.

With the proliferation of the clocks that synchronize modern digital circuits, a concomitant increase in their switching speeds (increasing emissions), and lower circuit voltages (increasing susceptibility), EMC increasingly became a source of concern. Many nations became aware of EMC as a growing problem and issued directives to the manufacturers of digital electronic equipment, which set out the essential manufacturer requirements before their equipment could be marketed or sold. Organizations in each nation and across Europe were set up to draw up and safeguard these directives.

More recently, the ever-increasing use of mobile communications and broadcast media channels has put huge pressure on the available airspace. Regulatory authorities are squeezing band allocations closer and closer together, relying on increasingly sophisticated EMC design methods, especially in the digital processing arena, to keep cross-channel interference to acceptable levels. Digital systems are inherently less susceptible than the old analogue systems, and also offer far easier ways (such as software) to implement highly sophisticated protection measures.

The Directive 2004/108/EC of the European Parliament and of the Council, of 15 December 2004, on the approximation of the Laws of Member States relating to electromagnetic compatibility governs on the one hand the electromagnetic emissions of this equipment in order to ensure that, in its intended use, such equipment does not disturb radio and telecommunication as well as other equipment. In the other the Directive also governs the immunity of such equipment to interference and seeks to ensure that this equipment is not disturbed by radio emissions normally present used as intended.

The main objective of the EMC Directive is thus to regulate the compatibility of equipment regarding EMC. In order to achieve this objective, provisions have been put in place so that:
- equipment (apparatus and fixed installations) needs to comply with the requirements of the EMC Directive when it is placed on the market and/or taken into service;
- the application of good engineering practice is required for fixed installations, with the possibility for the competent authorities of Member States to impose measures if non-compliances are established.

The conformity assessment for apparatus involves Self-Declaration by the manufacturer, with the voluntary option of using a Notified Body in the assessment of the manufacturer’s Technical File.

A transition period is in place for two years from 20 July 2007 for equipment placed onto the Community market prior to that date, provided no changes are made to the apparatus or to declared specifications.

Manufacturers attest to the conformity of their equipment to the provisions of the Directive by establishing an EC declaration of conformity and affixing the CE Mark. The equipment can then be placed on the European market without further regulatory constraints in respect of the aspects covered by the Directive.

It applies to the European Economic Area (EEA) and the territory of a number of candidate countries under a pre-accession agreement called a " PECA ".  In addition, via the mechanism of Mutual Recognition Agreements (MRAs), conformity assessment bodies under this Directive have been designated in a number of other trading blocks.

Guide is available to assist with the common application of the Directive 2004/108/EC which, whilst having no weight in law, deals with a number of practical issues that will be of interest to manufacturers. See the new PDF format Guide for the EMC Directive 2004/108/EC (21st May 2007) .

English Summary list of titles and references of harmonised standards relating to EMC

Company contacts
 Click here to see Authorized Dealers Worldwide
Company in Italy
 Click here to see Dealers and Companies represented in Italy
Product Catalog
Download the Product Catalog Short-Form Catalog
Online RMA
Check your RMA Status RMA Status
Downloads
 Download page Software
Manuals
Join Mailing List
  email Address:
  Name:



Valid XHTML 1.0 Transitional CSS Valid!       Top of Page    Copyright © Narda Safety Test Solutions S.r.l. MCMXCVIII-MMXVII. All rights reserved. PIVA 00972040091 http://www.livio.net/